| Author |
Message |
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
 Posted:
Sat Apr 16, 2005 4:04 am |
  |
Index the magnet so when you put it back in, it will be in the same spot. |
|
|
   |
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:04 am |
|
Nothing more than a magnet, really.............but it needs to rotate smoothly.  |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:05 am |
|
Just clean all the old grease off of it.......and apply new grease to the center hole.
DON'T GO CRAZY WITH THE GREASE! You don't want it spinning around inside the Dist. 
This is part #2 that OLD NASTY GREASE can cause SLOW MOVEMENT or even SIEZED TIMING ADVANCED!
|
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:05 am |
|
Keep your eyes open and watch out for this washer. |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:06 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:06 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:07 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:07 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:07 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:08 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:08 am |
|
If you have engine oil inside the Dist, this seal is leaking. Mitsu MD607405 |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:08 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:09 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:09 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:09 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:10 am |
|
There is a pressed in bearing at the bootom of the housing. Place some grease on it and flipr the Dist shaft over and push the grease up inside the bearing. Note the wear marks on the shaft from the bearing. |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:10 am |
|
Note the "D" shape at the top of the shaft and where the alignment marks are on the gear for proper re-assembly.
Dist O-ring MD602412 $3.69 retail $2.95 net. Yes, it's a special O-ring. |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:11 am |
|
REMEMBER, you should have taken this assembly apart and cleaned/re-lubed the "GUTS" too.
20 year old GREASE is not "SLICK"......which it needs to be!!! 
|
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:11 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:12 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:12 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:12 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:13 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:13 am |
|
|
|
|
JustPaus
Joined: 06 Oct 2004
Posts: 1656
Location: Gilbert, Arizona
|
| Posted:
Sat Apr 16, 2005 4:14 am |
|
|
|
|
|
|
